ads polyflex fittings
- In this RC Wares video, we will be discussing compression fittings, specifically Ford fittings, and their advantages over barbed fittings.
Advantages of Ford fittings:
- Minimizes friction loss in the system, making them ideal for long-distance or commercial projects.
- Provides better support and prevents the pipe from collapsing.
- Easy to transition between different types of pipes.
Types of Ford fittings:
- Coupling: used to connect two pieces of poly pipe.
- Poly by female: has female threads on one side and poly on the other.
- Male: used for transitioning to different types of pipes.
How to install Ford fittings:
- Use reinforcing inserts to prevent pipe collapse.
- Insert the inserts into the pipe and tap them in with a mallet.
- Insert the pipe into the fitting and tighten it with a pipe wrench.
- The gasket inside the fitting compresses against the pipe to hold it in place.
- While barbed fittings are more economical, Ford fittings are the best option for minimizing friction loss and providing support for the pipe. They are ideal for long-distance or commercial projects. Both types of fittings are available on seahorse.com. Don't forget to like and subscribe for more informative videos from RC Wares.
Barbed Fitting Troubles?...QUICK TIP GUARANTEED TO HELP!
- Sometimes it's difficult to get a barb fitting into polyflex or poly pipe, but there's a solution.
Tips for Fitting Barb Fittings into Polyflex:
- Heat up the polyflex with a heat gun until it's pliable.
- Slide the barb fitting into the warmed-up polyflex.
- Put a hose clamp on the barb to secure it in place.
- Let the polyflex cool and the hose clamp seal for a good seal.
- Using these tips will make fitting barb fittings into polyflex much easier and smoother.
- Subscribe to the channel and click the like button for more helpful tips.
How to Install Poly Pipe
Hey everybody, in this segment we're going to be talking about poly pipe. Poly is short for polyethylene, which is the black pipe used for irrigation systems. We'll be discussing how to put the fittings in and other tips for working with poly.
Poly pipe is a flexible and easy-to-install alternative to PVC for irrigation systems. It's important to use the correct fittings and clamps when installing poly pipe to ensure a tight seal.
Tips for Installing Fittings:
- Use high-quality fittings with sharp barbs for a secure seal.
- Poly fittings go on the inside of the pipe, while PVC fittings go over the pipe.
- Use a gear clamp or crimp clamp to secure the fitting to the pipe.
- For main lines, use two gear clamps and for secondary water, use oticor clamps.
- Low-density poly is more flexible and easier to work with, but not pressure rated. High-density poly is pressure rated and used for main lines.
- Use a mallet or torch to make it easier to install fittings.
- Do not use petroleum products like WD-40 on poly pipe.
- Use a saddle instead of a T for sprinkler heads.
Poly pipe is a great option for irrigation systems because it's easy to work with and flexible. By following these tips, you can ensure a secure and tight seal for your poly pipe system. If you have any questions, contact us at one of our stores.
Water Main Pipe Repair For A Home
This article discusses the process of repairing a leak in the water main to the house, specifically a cracked 3/4 inch polyurethane pipe. The leak caused water to run into the backyard, resulting in a muddy area and higher water bills. The author had to dig a five-foot hole to access the pipe and had to replace fittings both inside and outside the house. The author provides a step-by-step guide to the repair process, including materials needed and potential challenges.
Steps of the Repair Process:
1. Dig a five-foot hole to access the cracked polyurethane pipe.
2. Cut the old pipe and add a new piece going inside.
3. Put a clamp on and join two pieces of pipe together.
4. Replace the fitting inside the house and connect it to the copper piping.
5. Connect the new piece of pipe to the line going to the city water meter.
6. Patch the hole through the concrete foundation.
- 200 pounds per square inch plastic pipe
- Compression fittings
- Teflon tape
- Cement patch
- Finding the right materials and fittings
- Digging a hole without disrupting plants
- Connecting fittings in a tight space
- Ensuring proper sealing to avoid leaks
Repairing a leak in the water main to the house can be a challenging and time-consuming process, but it is important to address leaks to avoid higher water bills and potential damage to the house. The author recommends using compression fittings and proper sealing to ensure a permanent fix. With the right materials and approach, homeowners can successfully repair leaks in their water main and save money in the long run.
How to connect poly and PEX pipe/tubing together | Garage to Apartment Conversion | Episode 14
In this article, we will be discussing the process of installing a poly to PEX transition for plumbing and how to troubleshoot leaks. We will be examining the mistakes made in the previous attempt and how to avoid them.
1. Undoing previous work: Twist the PEX clamps off to remove the previous work.
2. Removing the PEX: Use heat to soften the PEX and squeeze the connection to remove it.
3. Adding the adapters: Use Teflon tape or thread sealant to screw the barbed fitting onto the adapter. Heat the poly pipe to soften it and slip it onto the adapter. Tighten the clamps.
4. Joining the connectors: Measure and cut the PEX to length. Slip on the connector and clamp it down with the crimping tool.
5. Testing the connection: Check for leaks and pressure to ensure a tight connection.
The process of installing a poly to PEX transition may seem daunting, but with the proper tools and technique, it can be done successfully. Avoiding the mistakes of previous attempts and troubleshooting leaks are crucial steps in ensuring a tight connection. By following the steps outlined above, you can complete this task with confidence.
All About Polyethylene Poly Pipe and Fittings
Polyethylene is a major piping system used in irrigation. It has several different versions, including a smaller kind and larger sizes. The smaller kind is half inch tubing, also known as swing pipe or funny pipe. The larger sizes, such as three quarter inch and one inch, are a major delivery system that is usually used in places with softer soil. Polyethylene is known for its ability to expand and contract more than PVC, making it useful in certain situations.
- The smaller kind of polyethylene tubing is used to run from PVC pipe to a head location, allowing for flexibility in positioning the head.
- The larger sizes of polyethylene tubing are useful in places with softer soil, as it can be delivered using a vibratory plow that only cuts a thin slit in the ground.
- Polyethylene tubing is inner diameter controlled, meaning the flow rate through different pipes is the same regardless of the outside diameter.
- Friction barb fittings are used with polyethylene tubing, with little sharp edges that grab hold of the inside of the pipe to keep it from pulling out.
- The fittings are put together with clamps, with the larger sizes requiring clamps due to higher psi levels.
- Pinch clamps are another option for putting together fittings, offering a no-leak seal without the risk of cracking the plastic fittings.
- The half inch polyethylene tubing can only carry four gallons per minute, making it only suitable for supplying one or two heads.
- Three quarter inch and one inch polyethylene tubing can flow up to eight and twelve gallons per minute, respectively.
Polyethylene is a versatile piping system used in irrigation, with several different versions to choose from. The smaller kind is useful for flexibility in positioning the head, while the larger sizes are better suited for softer soil. Fittings are put together using friction barbs and clamps, with pinch clamps offering another option for a no-leak seal. When considering flow rates, it's important to note that the half inch tubing can only carry four gallons per minute, making it only suitable for one or two heads.
How To Connect Barb Fitting to Water Line Using Hose Clamps
How to Connect a Water Line: Tips and Tricks
- Welcome to this tutorial on how to connect a water line
- Today we will be discussing the process of hooking up a one inch water line to a barbed fitting
Choosing the Right Pipe:
- It is recommended to choose a higher grade pipe for well or water line installation, such as 100 psi or 150 psi
- The pipe used in this tutorial is a one inch HDPE 250 psi pipe, which is thick and high quality
- However, this pipe can be stiff and difficult to work with, so extra care is needed during installation
- Hose clamps (opposite directions for a better fit)
- A propane torch for heating the pipe
- A barbed fitting (preferably brass)
- A valve
Connecting the Pipe:
- Heat the pipe carefully with a propane torch, making sure not to stay in one spot for too long
- Slide the heated pipe onto the barbed fitting, making sure it is bulging out properly
- Tighten the hose clamps as much as possible by hand
- Repeat the process for the other end of the water line
- Thanks for watching this tutorial on how to connect a water line
- If this video was helpful, please like and subscribe for more videos like this in the future!