#1 TikTok Ads Spy Tool

A Better Way to Make TikTok Ads Dropshipping & TikTok For Business

  • Find TikTok winning products & TikTok dropshipping ads.
  • Analyze TikTok advertisers
  • Get the Latest TikTok Shop Data.
Try It Free

ads single wall heavy duty pipe

Published on: July 6 2023 by pipiads

Advanced Drainage Systems is the world's largest manufacturer of corrugated high-density polyethylene drainage pipe. In this article, we will guide you on how to properly install a driveway culvert from ATS, an ideal solution to manage excess flow and prevent downstream flooding and erosion along a roadway.

Before You Start:

- Contact your local utility notification center to find out where any underground utility lines might be.

- Obtain any necessary permits for your project.

- Effective management of traffic during construction is necessary to reduce motorist traffic delays, ensure workers' safety, complete the project in a timely manner, and maintain access for businesses and residents.

Materials Needed:

- Flared end sections

- Pipe and pipe couplers

- Crushed stone for bedding

- Pipe embedment material

- Gravel for securing tote roff

- Concrete (if needed)

Installation Steps:

1. Excavate a trench from the outlet to the inlet point, allowing for positive drainage.

2. Place and compact crushed stone in the bottom of the trench as bedding for the pipe.

3. Cut the pipe to the appropriate length for your project, deburring the end if needed.

4. Start laying the pipe from the outlet point, making any fittings or coupler connections needed to reach the designated outlet point.

5. Install a flared end section for more effective drainage at the inlet and outlet points.

6. Secure the tote roff with gravel or concrete.

7. Backfill soil over the driveway sideslopes to allow for grass seating.

8. Place and compact the final backfill, then place and compact the subgrade material in preparation for the driveway.

Maintenance:

- Inspect and clean the system regularly.

- Check for erosion of the backfill and remove any large debris from the inlet and outlet structures that may obstruct the flow.

Installing a driveway culvert is a crucial step in controlling erosion and ensuring proper drainage around your home and lawn. ATS offers a variety of drainage solutions to meet your needs. Visit ATSpipe.com for more information.

DIY Don't Waste Your Money On Drain Pipe Couplers Make Them For $0

Hello everyone, it's DIY Guy 123 here with another DIY video. Today, I want to share with you a cheap and easy way to make couplers for your corrugated pipes.

Benefits of Making Your Own Couplers:

- Saves money

- Easy to make

- Can be used with perforated or non-perforated pipes

- Less strain on joints and unions

Steps to Make Your Own Couplers:

1. Take a piece of solid pipe

2. Use an angle grinder with a cutting wheel to open it up lengthwise

3. Fit the newly opened pipe onto the ends of two shorter pieces of pipe to join them together

4. Face the opening down to prevent debris from getting in

5. Enjoy your newly joined pipes with a cheaper coupler alternative

In conclusion, making your own couplers for corrugated pipes is a great way to save money and avoid unnecessary strain on joints and unions. It's easy to do with just a solid pipe and an angle grinder. So next time you need a coupler, try making your own and see the difference for yourself. And don't forget to subscribe to my channel for more DIY tips and tricks.

How to Install Dual Wall Culvert Pipe 101 for DIY'ers

Back to Basics: How to Install a Driveway Culvert Pipe

- The French Drain Man Channel's mission to help DIYers with their projects

- The importance of going back to the basics

Installing a Culvert Pipe 101

- The Baughman dual wall 24-inch diameter 20-foot in length culvert pipe

- Setting the pipe in the ground and packing stone on both sides

- Sizing the pipe for the elevation and ditch or swell

- Making sure to pack stone well for strength

- The simplicity of the installation process

- The importance of not making things too complicated

Installing the Baughman 18-inch Dual Wall Heavy Duty Culvert Pipe

- Using a long level to make sure the bubble is upstream

- The consequences of improperly installed culvert pipes

- The importance of blaming the person who installed the pipe

Closing Remarks

- The longevity of the Baughman tiles

- The experience and knowledge gained from lifelong work in the field

- The importance of doing it right the first time

- The French Drain Man Channel's commitment to helping DIYers

- The simplicity and importance of going back to the basics when it comes to installing a driveway culvert pipe.

HDPE Pipe Installation, Trench Preparation (Part 1)

Since its inception, corrugated high-density polyethylene (HDPE) pipe has become widely accepted as an innovative water conservation and drainage solution with several advantages over traditional pipe. This article aims to present the proper installation techniques for HDPE pipe, including trench preparation, pipe and fitting assembly, and backfill procedures.

Advantages of HDPE Pipe:

- Lightweight 20-foot lengths

- Wide range of diameters from 4 inches through 60 inches

- Convenient belen spigot joint for easy installation

- Annular corrugated exterior provides strength

- Smooth interior delivers superior hydraulics

- Excellent chemical and abrasion resistance for a long service life

Trench Preparation:

- Trench must be wide enough to place and compact the backfill material on either side of the pipe.

- Minimum trench widths are the outside diameter plus 16 inches for pipes 15 inches and smaller and 1.5 times the outside diameter plus 12 inches for pipes 18 inches and larger.

- Quality of the trench foundation is crucial, and the trench bottom must provide uniform long-term support to the pipe and backfill material.

- Soft materials like muck or refuse and hard irregular materials like bedrock require additional excavation.

- Trench boxes are necessary in some projects to provide a safe work area in the trench.

- The sub-trench allows for the compacted backfill below the trench box to remain undisturbed.

Pipe and Fitting Assembly:

- Inspection is necessary to eliminate rock outcroppings and remove all loose rocks and debris that could damage the pipe system.

- Four to six inches of approved bedding material can be placed in the trench.

- The outer two-thirds of bedding must be compacted as required.

- Joint integrity and installation quality are likely to be compromised if assembly takes place with water in the trench.

HDPE pipe has established a new standard of engineering and application excellence, making it ideal for stormwater management applications. Proper installation techniques, including trench preparation, pipe and fitting assembly, and backfill procedures, are crucial to ensure the longevity and effectiveness of the HDPE pipe system. Always refer to the pocket installation guide for specific guidelines and installation questions.

HDPE Pipe Installation, Backfill Procedures (Part 3)

When it comes to installing HDPE pipe, choosing the right backfill material is crucial for ensuring the pipe's performance and longevity. In this article, we will discuss the different types of backfill materials that can be used and their compaction requirements.

Types of Backfill Materials:

1. Class 1 Backfill Material:

- Consists of angular crushed stone or volcanic Eve

- Minimum compaction requirements are met by dumping the material into the trench and knifing it under the pipe's hunch

2. Class 2 Backfill Material:

- Consists of gravel and gravel sand mixtures

- Compaction is required

- Refer to the pocket installation guide for further definition of Class 2 materials and maximum lift heights between compaction efforts

3. Class 3 Backfill Material:

- Consists of silty gravels or sands

- Compaction is required

- Refer to the pocket installation guide for further definition of Class 3 materials and maximum lift heights between compaction efforts

Note: Native soils not identified as Class 1, 2, or 3 materials are generally not suitable as initial backfill materials.

Backfill Procedures:

- Always knife the backfill material under the hunch of the pipe to prevent voids and ensure even placement of backfill material around the pipe.

- Dump the material directly on top of the pipe so it falls equally on each side of the pipe to prevent shifting during the backfill process.

- The most critical area of the backfill structure is the envelope surrounding the pipe system. This envelope includes the bedding, the hunch area, and the initial backfill area.

- Only approved backfill material should be used in the bedding, hunch, and initial backfill areas of the trench.

- Final backfill material can be alternative or native material with the approval of the designing engineer.

- Pipes systems through 48-inch diameters require a minimum 12 inches of cover above the pipe. 54 and 60-inch pipes systems require a minimum 24 inches of cover above the pipe.

- Additional minimum cover is required for areas receiving heavy construction traffic.

- Mound and compact material over the pipe to provide the minimum cover needed during construction.

Choosing the right backfill material and following the proper backfill procedures is crucial for the successful installation of HDPE pipe. Following the recommended procedures outlined in this article and the pocket installation guide will ensure that you achieve quick, efficient, and successful installations of HDPE pipe.

DIY Installing a Culvert Pipe in the woods - 20' ADS Plastic

- The author discusses their experience installing culvert crossings on their property, including challenges and solutions.

Key Points:

- The author uses ADS culvert pipes for their durability and cost-effectiveness.

- The base and slope of the culvert crossings are crucial for proper water flow.

- The author had to bring the fill material for the culvert crossings over a long distance.

- Compacting the fill material is important to avoid damaging the culvert.

- The author plans to wait for the culvert to settle before deciding on a top covering.

- Landscape fabric and fieldstone can be used to stabilize the culvert ends and prevent erosion.

- The author's experience installing culvert crossings offers helpful tips and insights for others considering similar projects.

Commercial Drainage Job [ Baughman Tile Co. Yellow Pipe 6 inch ] Heavy Duty French Drain Pipe DIY

In this article, we will be discussing a commercial job that involves installing a French drain and a roof runoff system. The job site is on commercial property, and we will be working at an industrial plaza. We will go over the process of measuring and installing the systems, as well as the materials used.

Measuring and Installing the Systems:

- Measure 45 feet in the swale for the French drain.

- The French drain will run in the soil of a long lawn.

- Measure another 15 feet to the storm sewer.

- Go around the building to avoid barbed wire.

- Run the French drain to a big six-inch pipe connected to two downspouts.

- Use Boffman mini culvert pipe for the French drain.

- Use six-inch perforated pipe for the roof runoff system.

- Dig a trench big enough for two six-inch pipes for the French drain.

- Use virgin yellow pipe for the systems.

- The virgin pipe is stronger and longer-lasting than recycled pipe.

Materials Used:

- Boffman mini culvert pipe

- Virgin yellow pipe

- Tile tape

- Six-inch perforated pipe

- Monster clean outs

- Six-inch grate

This commercial job required careful planning and installation of a French drain and a roof runoff system. By using virgin yellow pipe and Boffman mini culvert pipe, we ensured that the systems would be strong and long-lasting. The trench was dug to accommodate two six-inch pipes to handle the heavy commercial traffic of the industrial plaza. Overall, this job was a success and will provide effective drainage for the property.

Start your free trial today!

Try Pipiads free for trial, no credit card required. By entering your email,
You will be taken to the signup page.